Wood-tone soffit above vertical metal siding

Metal Fascia & Soffit Installation on Vancouver Island

Metal fascia and soffit that finish the roofline and cover its edges, installed by a Red Seal-led sheet metal team from Shawnigan Lake. On their own, or with a new metal roof or siding.

What fascia and soffit do

Fascia is the board that runs along the edge of the roof. Soffit closes in the underside of the overhang. Together they finish the roofline.

They are easy to overlook until they are done well. A clad fascia gives the roof a sharp, even edge. A finished soffit makes the overhang look built, not left open.

Both are sheet metal work, bent and fitted along the whole roofline, and done by the same Red Seal-led crew that installs our roofs and siding. In Duncan, Jackie Wood had her fascia boards clad along with a new standing seam roof.

Wood-tone soffit installed on a two-storey home
Wood-tone soffit on a two-storey home

Who it suits

Any roofline that deserves a clean edge.

  • Homes getting a new roof

    Clad the fascia while the roof is being done, so the new edge matches the new roof.

    Standing seam metal roofing
  • New builds and custom homes

    Fascia and soffit planned in with the roof and walls from the start.

    New construction metal roofing
  • Re-siding projects

    New siding looks finished when the roofline above it is finished too.

    Metal siding
  • Multi-family and commercial

    Fascia, soffit and trim on larger buildings, alongside our cladding and sheet metal work.

    Commercial work

Reading a roofline

Three parts finish the edge of a roof. Scroll through them on one of our gables.

  1. Gable with charcoal metal fascia and wood-tone soffit above large windows

    01

    Fascia

    The board along the edge of the roof. Here it is clad in charcoal metal, so the edge is covered against the weather and reads as one crisp line from eave to peak.

  2. Gable with charcoal metal fascia and wood-tone soffit above large windows

    02

    Soffit

    The underside of the overhang. On a deep gable like this one it becomes a ceiling over the windows, finished in a warm wood tone with lights set into it.

  3. Gable with charcoal metal fascia and wood-tone soffit above large windows

    03

    Corners and returns

    Where the roofline turns at the bottom of the gable, the metal is cut and bent to close the corner cleanly. This is where careful sheet metal work shows.

Two-storey gable finished with wood-tone siding and soffit

How a fascia and soffit job works

Four steps, with the scope and timeline in writing before work starts.

  1. 1Free estimateWe look at the roofline with you, talk through colours and finishes, and answer your questions.
  2. 2Detailed written quoteClear scope, with a timeline for your project.
  3. 3InstallationFascia is clad and soffit installed along every edge, with the corners and returns trimmed to fit.
  4. 4Final walkthroughWe walk the finished roofline with you before we call the job done.

Built for wet coastal weather

The roof edge takes rain, wind and spray from every direction. It is the first place weather finds.

  • Exposed edges

    Fascia boards sit right at the edge of the roof. Clad in metal, the board is covered instead of left open to the rain.

  • Wind under the eaves

    Gusts push rain up and under the overhang. A closed, well-fitted soffit keeps it out of the roof framing.

  • Corners and joints

    Water looks for gaps where pieces meet. Trim cut and bent to fit closes them.

What clients say about the finish

5.0 on Google

“Stellar Metal Exteriors did our standing seam metal roof in Duncan plus they cladded our fascia boards. They were reliable and did an excellent job with the roof. I am so happy with the way it turned out.”
Jackie Wood · Duncan · Google review
“Stellar Metal absolutely killed it on my project. They handled all the custom window frames, fascia on the gable ends, door trim, perimeter edging and the level of craftsmanship was seriously impressive. Everything was clean, precise, and clearly done by guys who take real pride in their work…”
Shawn Blom · Google review
BBB Accredited BusinessRated 5.0 from 5 Google reviews.

Fascia and soffit questions

Straight answers from a Red Seal sheet metal worker. Anything else, just ask.

Call (250) 634-2230

Yes. Estimates are free and come with a detailed quote.

Yes. Stellar Metal Exteriors is licensed, insured and registered with WorkSafeBC, and is a BBB Accredited Business.

Get a free estimate for fascia and soffit

Tell us about the roofline: the house, roughly how much edge, and whether a roof or siding job is happening too.

What happens next

  1. 1Send the form or callTell us about the roof, siding or building.
  2. 2Free estimateWe look at the project and talk through options.
  3. 3Detailed written quoteClear scope, with a timeline for your project.
  4. 4InstallationMost metal roofs are finished within a month. Larger projects can take longer.
(250) 634-2230stellarmetalex@gmail.comOpen 7 days, 9 a.m. to 5 p.m.

Request a Free Estimate

Project type

We only use your details to reply about your project. Privacy Policy

CallGet a Free Estimate