Teal vertical metal siding around tall white-trimmed windows on a float home

Custom Metal Flashing, Fabricated & Installed on Vancouver Island

Window, door, chimney, cap and roof flashing, bent to fit the building and installed by a Red Seal-led sheet metal team from Shawnigan Lake. For homes, new builds and commercial buildings across Vancouver Island.

What custom flashing is

Flashing is the formed sheet metal that seals the joints of a building: where a roof meets a wall, where a window or door sits in the siding, and along every edge and cap.

Stock flashing comes in a few standard shapes. Custom flashing is bent to the angles and lengths of the building it goes on, so it sits tight and sends water where it should go.

It is the heart of the sheet metal trade. We fabricate and install it ourselves, led by a Red Seal sheet metal worker with 18 years in the trade.

Custom metal chimney cladding on a brown metal roof with mountain views
Custom metal chimney cladding on a brown standing seam roof

Every edge on one float home

The teal float home below is finished in metal siding, and every edge around it is custom trim and flashing we made to fit.

Teal vertical metal siding around tall white-trimmed windows on a float home
Teal vertical metal siding with white custom trim on a float home
  1. Custom window frames

    Each tall window is wrapped in white metal trim, bent to the depth of the opening so it sits tight to the frame.

  2. Fascia on the gable end

    The sloped top edge is finished in metal, so the roofline reads as one clean line.

  3. Corner trim

    Where two walls meet, a single trim piece closes the corner and covers the panel ends.

  4. Perimeter edging

    A continuous edge along the base of the walls finishes the siding at the bottom.

The owner, Shawn Blom, wrote about the window frames, gable fascia, door trim and edging in his Google review. Read his review

Where we make and fit flashing

On homes, new builds and commercial buildings, new or existing.

  • Teal vertical metal siding on a float home entry with a wood canopy

    Windows and doors

    Head flashing, frames and trim around openings, so water runs out and away instead of in behind the siding.

    Metal siding
  • Brown standing seam metal roof with a clad chimney surrounded by forest

    Chimneys

    Chimney cladding and flashing made to suit the roof it sits on, tied in with the panels around it.

    Standing seam roofing
  • Custom-bent metal cap flashing on a low wall

    Caps on walls and parapets

    Cap flashing bent to the width of the wall, from low garden walls to commercial parapets.

    Architectural sheet metal
  • Grey standing seam metal roof with valleys and a dormer

    Roof edges and valleys

    Ridges, hips, valleys and the junctions where a roof meets a wall or dormer.

    Metal roof repairs

Where Vancouver Island weather gets in

Water usually gets in at the joints: the edges, openings and junctions that flashing is there to close.

  • Wind-driven rain

    Coastal storms push rain sideways and up under edges. Flashing that laps the right way keeps it on the outside.

  • Openings

    Windows, doors and chimneys break the wall or roof. Each one needs metal shaped to lead water around it.

  • Long wet seasons

    Months of rain find any gap. Tight, well-fitted flashing is what keeps the structure behind it dry.

Close-up of a standing seam metal roof hip and ridge detail

How a flashing job works

Four steps, with the scope and timeline in writing before work starts.

  1. 1Free estimateWe look at the roof, wall or opening with you and talk through what the flashing needs to do.
  2. 2Detailed written quoteClear scope, with a timeline for your project.
  3. 3Fabrication and installationWe bend the flashing to suit the job and install it ourselves, so every corner and lap fits.
  4. 4Final walkthroughWe walk the finished work with you before we call the job done.

What clients say about the details

5.0 on Google

Float home in a marina finished with teal vertical metal siding
“Stellar Metal absolutely killed it on my project. They handled all the custom window frames, fascia on the gable ends, door trim, perimeter edging and the level of craftsmanship was seriously impressive. Everything was clean, precise, and clearly done by guys who take real pride in their work…”
Shawn Blom · Google review
“Stellar Metal Exteriors did our standing seam metal roof in Duncan plus they cladded our fascia boards. They were reliable and did an excellent job with the roof. I am so happy with the way it turned out.”
Jackie Wood · Duncan · Google review
BBB Accredited BusinessRated 5.0 from 5 Google reviews.

Custom flashing questions

Straight answers from a Red Seal sheet metal worker. Anything else, just ask.

Call (250) 634-2230

Yes. Estimates are free and come with a detailed quote.

Yes. Stellar Metal Exteriors is licensed, insured and registered with WorkSafeBC, and is a BBB Accredited Business.

Get a free estimate for custom flashing

Tell us what needs flashing: the roof, wall, window or chimney, and roughly how much.

What happens next

  1. 1Send the form or callTell us about the roof, siding or building.
  2. 2Free estimateWe look at the project and talk through options.
  3. 3Detailed written quoteClear scope, with a timeline for your project.
  4. 4InstallationMost metal roofs are finished within a month. Larger projects can take longer.
(250) 634-2230stellarmetalex@gmail.comOpen 7 days, 9 a.m. to 5 p.m.

Request a Free Estimate

Project type

We only use your details to reply about your project. Privacy Policy

CallGet a Free Estimate