Custom metal cap flashing along a flat roof parapet

Architectural Sheet Metal Contractor on Vancouver Island

Copings, parapet caps, cladding details and custom trim for commercial and multi-family buildings across Vancouver Island. Fabricated and installed by a Red Seal-led sheet metal team based in Shawnigan Lake.

Red Seal · Licensed & insured · WorkSafeBC registered · BBB Accredited

What architectural sheet metal is

Architectural sheet metal is the custom-bent metal that finishes a building: the caps on its parapet walls, the trim at its corners and windows, the cladding on its chimney.

None of it comes off a shelf. Each piece is cut and bent to fit the wall, edge or opening it covers. Those details sit on every edge of a building, in plain sight, and they are a big part of how well it keeps the weather out.

It is the core of the sheet metal trade. Stellar is owner-operated by Cameron Bigelow, a Red Seal sheet metal worker with 18 years in the trade, and we fabricate the sheet metal as well as install it.

Custom metal chimney cladding on a brown metal roof with mountain views
Custom metal chimney cladding on a brown metal roof

Built for Vancouver Island weather, one detail at a time

Long wet winters and wind off the water drive rain at the top of every wall. On a flat-roofed building the parapet cap takes the worst of it. Here is what a well-made one does.

PARAPETROOFEXTERIOR12345
Detail 01 · Parapet coping capTypical section · Not to scale
  1. 1

    Top falls toward the roof

    Rain on the cap runs back onto the roof instead of down the face of the building.

  2. 2

    Outside face laps the cladding

    It covers the top edge of the wall cladding, where water would otherwise get in behind it.

  3. 3

    Kicked drip edge

    A hemmed edge, bent out from the wall, throws water clear instead of letting it run down the face.

  4. 4

    Inside face laps the roof side

    The cap comes down over the roof side of the parapet as well, so the wall is covered on all three sides.

  5. 5

    Membrane turns up under the cap

    The roof membrane runs up the inside of the parapet and the cap laps over it, so the two overlap.

Custom-bent metal cap flashing on a low wall
Every cap is bent to fit its wall.Two lengths of cap joined with a raised seam, on one of our jobs.
Teal vertical metal siding around tall white-trimmed windows on a float home

What we fabricate and install

Bent to fit and installed by the same team: the pieces that finish a building's edges, on commercial work and on homes.

  • 01Copings and parapet caps

    For flat-roofed commercial and multi-family buildings, like the parapet at the top of this page.

  • 02Cap flashing

    On low walls, ledges and exposed wall tops, bent to suit the profile.

    Custom flashing
  • 03Cladding trim and transitions

    Corners, edges and the joins between ACM panels, metal siding and other materials.

    ACM panels
  • 04Window and door trim

    Custom window frames, door trim and perimeter edging, like the float home pictured.

  • 05Fascia cladding

    Metal cladding over fascia boards, finished cleanly at the gable ends.

    Fascia & soffit
  • 06Chimney cladding

    Chimneys clad in metal to suit the roof, like the one pictured above.

Who we do this work for

Commercial and multi-family buildings first, and homes with modern details.

  • General contractors and builders

    Sheet metal quoted from your drawings, with a clear written scope and timeline. We have worked alongside general contractors including JBL Construction.

    Commercial work
  • Developers and property managers

    Copings, caps and trim on multi-family and commercial buildings, with proof of WorkSafeBC coverage and insurance available on request.

  • Storefronts and ACM facades

    The flashing and trim around ACM panels, fabricated by the same team that installs the panels. We installed the ACM storefront at Woodgrove Mall in Nanaimo.

    Woodgrove Mall storefront
  • Custom homes

    Window frames, gable fascia, door trim and perimeter edging on modern homes, like the float home above.

    Custom metal flashing

The sheet metal trade on your project

For general contractors, developers and property managers who need the edges of a building done properly.

  • Owner-operated by a Red Seal sheet metal worker, 18 years in the trade
  • We fabricate the sheet metal as well as install it
  • Licensed and insured, registered with WorkSafeBC
  • BBB Accredited Business
  • Proof of WorkSafeBC coverage and insurance available on request
  • We have worked alongside general contractors including JBL Construction

From drawings to the last cap

  1. 1Send drawings or a scopeEmail drawings, elevations or a scope of work to stellarmetalex@gmail.com, or use the form below.
  2. 2Review and questionsWe go through the scope and details with you, and look at the site when it helps.
  3. 3Detailed written quoteClear scope, with a timeline for your project.
  4. 4Installation and walkthroughRed Seal-led installation, then a final walkthrough with your site lead.

Detail work clients notice

5.0 on Google

Float home in a marina finished with teal vertical metal siding
“Stellar Metal absolutely killed it on my project. They handled all the custom window frames, fascia on the gable ends, door trim, perimeter edging and the level of craftsmanship was seriously impressive. Everything was clean, precise, and clearly done by guys who take real pride in their work…”
Shawn Blom · Google review
“Stellar Metal Exteriors did our standing seam metal roof in Duncan plus they cladded our fascia boards. They were reliable and did an excellent job with the roof. I am so happy with the way it turned out.”
Jackie Wood · Duncan · Google review
BBB Accredited BusinessRated 5.0 from 5 Google reviews.

Architectural sheet metal questions

Straight answers from a Red Seal sheet metal worker. Anything else, just ask.

Call (250) 634-2230

Yes. Estimates are free and come with a detailed quote.

Yes. We install ACM (aluminum composite material) panels for commercial buildings, including a storefront at Woodgrove Mall in Nanaimo.

Yes. Stellar Metal Exteriors is licensed, insured and registered with WorkSafeBC, and is a BBB Accredited Business.

Request an architectural sheet metal quote

Send drawings, elevations or a few photos of the building. You get a detailed, written quote.

What happens next

  1. 1Send the form or callTell us about the roof, siding or building.
  2. 2Free estimateWe look at the project and talk through options.
  3. 3Detailed written quoteClear scope, with a timeline for your project.
  4. 4InstallationMost metal roofs are finished within a month. Larger projects can take longer.
(250) 634-2230stellarmetalex@gmail.comOpen 7 days, 9 a.m. to 5 p.m.

Request a Commercial Quote

Send drawings to stellarmetalex@gmail.com

Project type

We only use your details to reply about your project. Privacy Policy

CallGet a Free Estimate